 |
| LKHex-
10 with shroud and legs |
Applications
The LKHex pump is a highly efficient and economical
centrifugal pump, which meets the requirements of the ATEX directive 94/9
IEC group II, categories 2 and 3, temperature class T3 and T4. LKHex is
available in nine sizes, LKHex-10, -15, -20, -25, -35, -40, -45, -50, -60.
The LKHex performance data are equal to the performance of LKH pump.
Standard design
The LKHex pump consists of motor, stub shaft, mechanical
compression coupling, adaptor, back plate, impeller, pump casing and shaft
seal.
The LKHex has a stainless steel shroud for protection of
the motor, and the complete unit is supported on four adjustable stainless
steel legs.
Shaft seals
The LKH pump is equipped with either a single shaft seal
or a double mechanical shaft seal. The seal ring is in acid-resistant
steel AISI 329 with sealing surface in silicon carbide and rotating seal
rings in carbon or silicon carbide.
Materials
| Product wetted steel parts: |
Acid-resistant steel 1.4404 (316L). |
| Other steel parts: |
Stainless steel 1.4301 (304). |
| Finish: |
Semi bright. |
| Product wetted seals: |
EPDM, NBR, FPM and FEP. |
Technical data
| Max. inlet pressure: |
LKHex (50/60 Hz): 1000 kPa (10 bar). |
| Product temperature (T4): |
-10°C to +80°C (NBR).-10°C to +110°C (EPDM, FPM, FEP). |
| Product temperature (T3): |
-10°C to +80°C (NBR).-10°C to +110°C (EPDM).-10°C to +140°C (FPM,
FEP). |
| Ambient temperature: |
-10°C to +30°C |
Double mechanical shaft seal (DMS):
| Water pressure inlet, LKH-10 to -60: |
Max. 500 kPa (5 bar). |
| Water consumption: |
0.25 -0.5 l/min. |
Connections for DMS:
R 1/8" (BSP) external thread.
Motor
Foot-flanged ATEX approved motor according to the IEC
metric standard, 2 poles = 3000/3600 rpm. at 50/60 Hz.
Voltage and frequency
| 50 Hz |
EEx d & EEx d(e) |
230V Δ/400VY |
≤ 7.5 kW |
| EEx d & EEx d(e) |
400V Δ/690VY |
≥ 11 kW |
| 60 Hz |
EEx d & EEx d(e) |
440-480VY |
≤ 7.5 kW |
| EEx d & EEx d(e) |
440-480V Δ |
≥ 11 kW |
| 50 Hz |
EEx e |
220-240V Δ/380-420VY |
≤ 4 kW |
| EEx e |
380-400V Δ |
≥ 5.5 kW |
| 60 Hz |
EEx e |
440-480V Y |
≤ 4 kW |
| EEx e |
440-460V Δ |
≥ 5.5 kW |
Motor sizes
50 Hz: 1.5 - 2.2 - 3 - 4 - 5.5 - 7.5 - 11 - 15 -
18.5 - 22 kW.
60 Hz: 1.75 - 2.5 - 3.5 - 4.6 - 6.4 - 8.6 - 12.5 - 17 - 21 - 25 kW.
Dimensions
Note that most of the dimensions depend on motor supplier
and motor size. Non-dependent dimensions are equal to the dimensions for
LKH.
Flow chart
Frequency 50 Hz, Speed (Synchr): 3000 rpm
Connections (mm) Sanitary version
| LKHex-10, -20, -35 |
| Dl 63.5 |
ISO |
ISO |
DIN |
SMS |
BS |
DS |
| Dll 51 |
Clamp |
Male |
Male |
Male |
Male |
Male |
| Ml |
21 |
21 |
25 |
24 |
27 |
24 |
| Mll |
21 |
21 |
22 |
20 |
27 |
20 |
| LKHex-25 |
| Dl76.1 |
ISO |
ISO |
DIN |
SMS |
BS |
DS |
| Dll 63.5 |
Clamp |
Male |
Male |
Male |
Male |
Male |
| Ml |
21 |
21 |
30 |
24 |
27 |
24 |
| Mll |
21 |
21 |
25 |
24 |
27 |
24 |
| LKHex-40 |
| Dl76.5 |
ISO |
ISO |
DIN |
SMS |
BS |
DS |
| Dll63.5 |
Clamp |
Male |
Male |
Male |
Male |
Male |
| Ml |
21 |
21 |
30 |
24 |
27 |
24 |
| Mll |
12 |
21 |
27 |
24 |
22 |
21 |
| LKHex-15, -45, -50 |
| Dl101.6 |
ISO |
ISO |
DIN |
SMS |
BS |
DS |
| Dll76.1 |
Clamp |
Male |
Male |
Male |
Male |
Male |
| Ml |
21 |
21 |
30 |
35 |
32 |
24 |
| Mll |
12 |
21 |
30 |
24 |
27 |
24 |
| LKHex-60 |
| Dl101.6 |
ISO |
ISO |
DIN |
SMS |
BS |
DS |
| Dll101.6 |
Clamp |
Male |
Male |
Male |
Male |
Male |
| Ml |
21 |
21 |
30 |
35 |
32 |
24 |
| Mll |
21 |
21 |
30 |
35 |
32 |
24 |
| LKHex-60 |
| DlDN150 |
DIN |
Dl 6" |
ISO |
| DllDN100 |
Male |
Dll 4" |
Clamp |
| Ml |
50 |
Ml |
38 |
| Mll |
30 |
Mll |
16 |
Options
- - Impeller with reduced diameter.
- - Motor for other voltage and/or frequency.
- - 1500 rpm. motor.
- - Counter flanges, seal rings and bolts for flanged connections
(industrial version).
- - Wider clearance between impeller and backplate if there is a risk
of building up a hard layer of product.
(Standard clearance is 0.5 mm and can be made up to 2.5 mm).
- - Surface roughness, product wetted parts:
Ra ≤ 0.8 mm.
- - Product wetted seals of Nitrile (NBR), Fluorinated rubber (FPM) or
FEP.
- - Rotating seal ring of Silicon Carbide.
Ordering
Please state the following when ordering:
- - Pump size.
- - Connections.
- - Impeller diameter.
- - Motor size.
- - Voltage and frequency.
- - Flow, pressure, ambient and media temperature.
- - Atmosphere ignition temperature.
- - Group category and temperature class.
- - Density and viscosity of the product.
- - With or without shroud.
- - Shaft seal material.
Note!
For further details, see also IM 70969.
This product has EHEDG certification.
This product is complient with the ATEX directive. |
